Zanussi ZWG5140P Bedienungsanleitung

ENUser manualWashing MachineZWG 5140 P

• Always use a correctly installed shockproof socket.• Do not use multi-way plugs, connectors and extensioncables. There is a risk of fire.• Do not re

Grass: soap lightly and treat with bleach (whites and fastcoloureds only).Ball point pen and glue: moisten with acetone1), lay thegarment on a soft cl

If the water hardness degree is medium or high we sug-gest you to add a water softener following always themanufacturer’s instructions.When the degree

Warning! Do not use the flap in "DOWN" positionwith:• Gelatinous detergent or thick detergent.• Powder detergent.• With programmes with prew

1Programme selector dialSyntheticaMixFijne was5 overhemdenMini 30JeansAnti-kreukKatoenKatoen + voorwasKatoen ecoSpoelenPompenCentrifugerenWol/HandwasT

44 u8 uStartuitstelThe start of the programme can be delayed by 8 or 4 hours by means of thisbutton. The relevant light illuminates.You must select th

6Start/PauzeStart the programme by pressing the button 6• To start the selected programme, press the button 6, the correspondinggreen pilot light stop

Stand by: during programme setting up and oncethe programme has finished, if the programme se-lector dial and any button are not touched, after a few

Programme - Maximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fabrics Load - Typeof LaundryOptionsDetergent Com-part

Programme - Maximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fabrics Load - Typeof LaundryOptionsDetergent Com-part

ContentsSafety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4Environment concerns _ _ _ _

Standard programmes for the Energy Label consumptionvaluesThe cotton 60 °C economy and cotton 40 °C economy arethe standard cotton programmes for norm

• turn the drum and alignthe filter cover (FILTER)with the arrow on thedoor seal;• open the filter cover bypressing the specialhook and by rotatingthe

• Screw the hose back onto the tap. Make sure theconnection is tight.• Unscrew the hose fromthe appliance. Keep atowel nearby becausesome water may fl

Fault code and malfunction Possible cause / SolutionExtra spoelenEindeHoofdwasStart/PauzeThe light of button 6 flashesand the light 7.2 illuminates:Pr

Malfunction Possible cause / SolutionThe appliance does not start:The plug is not properly inserted in the power socket.• Insert the plug into the pow

Malfunction Possible cause / SolutionSpinning starts late or the ap-pliance does not spin:The electronic unbalance detection device has cut in because

26

27

www.zanussi.com/shop 132933530-A-262011

not pressing the electrical supply cable against thewall.• Install the appliance on a flat hard floor.• Never place cardboard, wood or similar materia

To activate this device, ro-tate the button (withoutpressing it) inside thedoor clockwise until thegroove is horizontal. Ifnecessary use a coin.To dis

>PP<=polypropyleneThis means that they can be recycled by disposing ofthem properly in appropriate collection containers.Ecological hintsTo save

Electrical connection VoltageOverall powerFuseFrequency230 V2200 W10 A50 HzWater supply pressure MinimumMaximum0,5 bar (0,05 MPa)8 bar (0,8 MPa)Level

• Return appliance to it'supright position.• Open the door and re-move the plastic hoseguide, the bag contain-ing the instructionbooklet and the

Positioning and levellingx 4Level the appliance by raising or lowering the feet.The appliance MUST be level and stable on a flat hardfloor. If necessa

Push the drain hose onto the spigot and secure with aclip, ensure a loop is formed in the drain hose to pre-vent waste from the sink entering the appl