Zanussi ZDT6053 Bedienungsanleitung PDF herunterladen (Seite 6)

Before using your dishwasher for the first time:

1. Ensure that the electrical and water connections comply

with the installation instructions

2. Remove all packaging from inside the appliance

3. Set the water softener

4. Pour 1 litre of water inside the salt container and then fill

with dishwasher salt

5. Fill the rinse aid dispenser

The water softener

The dishwasher is equipped with a water softener designed to

remove minerals and salts from the water supply, which would

have a detrimental or adverse effect on the operation of the

appliance.

The higher the content of these minerals and salts, the harder

your water is.

Water hardness is measured in equivalent scales, Clarke

degrees, French degrees (°TH) and mmol/l (millimol per litre -

international unit for the hardness of water).

The softener should be adjusted according to the hardness of

the water in your area. Your local Water Authority can advise

you on the hardness of the water in your area.

The water softener must be set in both ways: manually, using

the water hardness dial and electronically, by the means of the

programme selection/cancel button.

a) Setting manually

1. Open the dishwasher door.

2. Remove the lower basket from the dishwasher.

3. Turn the water hardness dial to position 1 or 2 (see table).

4. Replace the lower basket.

The dishwasher is factory set

at position 2.

b) Setting electronically

The dishwasher is factory set at level 5.

1. With the dishwasher switched off, press the On/Off button.

The END OF CYCLE indicator light flashes (setting mode).

In case salt and/or rinse aid refilling is necessary the

corresponding indicator lights illuminate.

If one of the washing programme indicator lights is on, this

means that a washing programme has been set.

The setting must be cancelled: press for about 3 seconds

the programme selection/cancel button; the indicator

light of the set programme turns off and the END OF

CYCLE indicator light flashes, indicating that the set

programme has been cancelled and that the machine is

now in setting mode.

2. Press and keep pressed the programme selection/cancel

button until programme indicator light 1 flashes and

programme indicator light 2 illuminates with a fixed light.

Wait until programme indicator light 2 turns off, programme

indicator light 1 goes on flashing and simultaneously the

END OF CYCLE indicator light starts flashing.

This indicates that you have activated the electronic setting

function of the water softener.

The current level is indicated by a sequence of flashes of

the END OF CYCLE indicator light, a sequence of

intermittent audible signals and a pause of a few seconds

(see chart).

Example: 5 flashes/5 audible signals + pause +

5 flashes/5 audible signals etc...= level 5

3. To change the level, press the programme

selection/cancel button.

Each time the button is pressed the level changes. (For the

selection of the new level, see chart).

Examples:

if the current level is 5, by pressing the programme

selection/cancel button once, level 6 is selected.

if the current level is 10, by pressing the programme

selection/cancel button once, level 1 is selected.

The END OF CYCLE indicator light remains off for a few

seconds and then starts flashing indicating the new

selection is set.

4. To memorise the operation, switch off the machine by

pressing the On/Off button or wait for about 60 seconds,

after which the machine will automatically return to setting

mode.

Prior to using for the first time

Clarke

°TH

mmol/l

manually electronically

64 - 88

53 - 63

46 - 52

36 - 45

28 - 35

23 - 27

18 - 22

13 - 17

5 - 12

< 5

9,0 - 12,5

7,6- 8,9

6,5 - 7,5

5,1 - 6,4

4,0 - 5,0

3,3 - 3,9

2,6 - 3,2

1,9 - 2,5

0,7 - 1,8

< 0,7

Range

III

I/II

91 - 125

76 - 90

65 - 75

51 - 64

40 - 50

33 - 39

26 - 32

19 - 25

7 - 18

< 7

level 10

level 9

level 8

level 7

level 6

level 5

level 4

level 3

level 2

level 1

yes

Water hardness

Adjusting the

water hardness

setting

Number of flashes

of the

"END OF CYCLE"

indicator light

Use of

salt

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Zanussi ZDT6053 Bedienungsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Zanussi ZDT6053