ENUser manualWashing MachineZWN 7100 LZWN 7120 L
For the compatibility among the washing pro-grammes and the options see chapter «Wash-ing programmes».Start the programme by pressing button 7To start
turning the selector dial to . After a few mi-nutes the door can be opened.(Pay attention to the water level and tem-perature!).After closing the do
Ball point pen and glue: moisten with ace-tone1), lay the garment on a soft cloth and dabthe stain.Lipstick: moisten with acetone as above, thentreat
Washing programmesProgrammeMaximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fab-rics Load - Type of LaundryOptionsD
ProgrammeMaximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fab-rics Load - Type of LaundryOptionsDetergent Com-partm
ProgrammeMaximum and Minimum Temperature - Cycle De-scription - Maximum Spin Speed - Maximum Fab-rics Load - Type of LaundryOptionsDetergent Com-partm
Remove the drawerby pressing the catchdownwards and bypulling it out. Flush itout under a tap, to re-move any traces ofaccumulated powder.To aid clean
Replace the filter intothe pump by insertingit correctly into thespecial guides.Screw the pump cov-er firmly by turning itclockwise.Close the pump doo
• if necessary, wait until the water has cooleddown;• open the pump door;• place a bowl on the floor and place the endof the emergency emptying hose i
Problem Possible cause/SolutionThe machine does not fill:The water tap is closed. • Open the water tap.The inlet hose is squashed or kinked. • Check t
ContentsSafety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 4Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Problem Possible cause/SolutionThe machine vibrates isnoisy:The transit bolts and packing have not been removed.• Check the correct installation of th
Spin Speed Maximum 1000 rpm (ZWN7100L)1200 rpm (ZWN7120L)Consumption valuesThe data of this table are approximate. Different causes can change the dat
After removing all thepackaging, carefullylay machine on it'sback to remove thepolystyrene basefrom the bottom.Remove the powersupply cable and t
Connect the hose toa tap with a 3/4”thread. Always usethe hose suppliedwith the appliance.35°45°The other end of the inlet hose which con-nects to the
Caution! Should the appliance powersupply cable need to be replaced,this must be carried out by a ServiceCentre.Environmental concernsThe symbol on
25www.zanussi.com
26 www.zanussi.com
27www.zanussi.com
www.zanussi.com/shop 192986481-A-112012
• When unpacking the appliance, check that itis not damaged. If in doubt, do not use it andcontact the Service Centre.• All packing and transit bolts
Product description1Detergent dispenser drawer2Control panel3Door opening handle4Rating plate5Drain pump6Adjustable feet123456Detergent dispenser draw
Flap for powder or liquid deter-gent (see "Flap for powder or liquid deter-gent" in the chapter "Daily use" for more de-tails).Co
Programme selector dial, spin speed button and availableoptionsProgramme Selector DialIt allows you to switch the appliance on/off and/or to select a
After selecting a programme, the duration isdisplayed in hours and minutes (for example ). The duration is calculated automati-cally on the basis of t
Daily useLoad the laundryOpen the door bycarefully pulling thedoor handle out-wards. Place thelaundry in the drum,one item at a time,shaking them out
• Measure out thedetergent.• Pour the powderdetergent into themain wash com-partment .• Remove the remaining powder formthe flap.• There is remaining
Kommentare zu diesen Handbüchern