Zanussi Z712W43BI Bedienungsanleitung

GETTING STARTED?EASY.User ManualZ712W43BIEN User ManualWashing Machine

553 mm596 mm140 mm76 mm50 mm50 mm819 mmIf hoses run behind the appliance, makesure that nothing closes the small re-cess indicated with the measures 5

1. Remove the screws of the top cover on the rear ofthe appliance and install the anti-tilting device asshown in the drawing.~10mm2. Adjust the anti-t

Reversibility of the cupboard doorCarry out the cupboard door reversibility before theappliance is built in completely.MNOIf the cupboard door has to

16-22 mm22±1,5 mm449mm595-598 mmØ 35 mm12,5 - 14 mmSet the position of the lower hole respecting dimen-sions and distances shown in the drawing (449mm

2N1EDCCounter-magnetThe appliance is pre set for a magnetic closure.For a correct closure:1. Position the screw C and the counter-magnet Don the magne

CONTROL PANELCONTROL PANEL DESCRIPTION12349 657810The permanent options are set byholding pressed the relative button for3 seconds at least.1Programme

DISPLAYA B CADoor locked indicator.BChild safety lock indicator.CThe digital indicator can show:• Programme duration (e. g. ).• Delay time (e. g. ).

To activate/deactivate this option , hold downthe Prewash button until relevant indicator comes on/goes off.•SPIN When you set a programme, the appl

PROGRAMMESPROGRAMME CHARTProgrammeDefault tempera-tureTemperaturerangeReferencespin speedSpin speedrange(rpm)MaximumloadProgramme description(Type of

ProgrammeDefault tempera-tureTemperaturerangeReferencespin speedSpin speedrange(rpm)MaximumloadProgramme description(Type of load and soil level)Machi

SAFETY INFORMATIONBefore the installation and use of the appliance, carefully read thesupplied instructions. The manufacturer is not responsible for

ProgrammeDefault tempera-tureTemperaturerangeReferencespin speedSpin speedrange(rpm)MaximumloadProgramme description(Type of load and soil level)Wool/

ProgrammeSpinPrewashDelay StartFlextimeSpin/Drain Rinse Machine Clean Duvet Daily Wash

Programmes Load (kg)Energy con-sumption(kWh)Water con-sumption (li-tre)Approximateprogrammeduration(minutes)Remainingmoisture(%)1)Cottons40°C7 1.00 80

BEFORE FIRST USE1. Make sure that the electrical power is availableand the water tap is open.2. Pour 2 litres of water into the detergentcompartment m

CHECK THE POSITION OF THE DETERGENTFLAP1. Pull out the detergent dispenser until it stops.2. Press the lever down to remove the dispenser.3. To use po

3. Touch the Start/Pause button again tostart the new countdown.THE AUTOADJUST SYSTEM LOADDETECTIONAfter touching the Start/Pause button:1. The Au

• The door stays locked.• You must drain the water to open the door:1. If necessary, touch the Spin button to decreasethe spin speed proposed by the a

Special stain removers are available. Use thespecial stain remover that is applicable to the typeof stain and fabric.DETERGENTS AND OTHER TREATMENTS•

Regularly examine the seal and remove all objectsfrom the inner part. Coins, buttons, other smallitems forgotten in the pockets of your clothes aredep

without any clothes in the drum.CLEANING THE DRAIN PUMPWARNING! Disconnect the mainsplug from the mains socket.Regularly check the drain pump filteran

– areas for communal use in blocks of flats or in launderettes.• Do not exceed the maximum load of 7 kg (refer to the"Programme chart" chapt

180˚3. Turn the filter 180 degrees in anti-clockwise direc-tion to open it, without removing. Let the water flowout.4. When the bowl is full of water,

219. Put the filter back into the special guides by turningit clockwise. Make sure that you tighten the filter cor-rectly to prevent leakages.1210. Cl

EMERGENCY DRAINIf the appliance cannot drain the water, carry outthe same procedure, described in 'Cleaning thedrain pump' paragraph. If nec

POSSIBLE FAILURESProblem Possible solutionThe programme does notstart.• Make sure that the mains plug is connected to the mains socket.• Make sure tha

Problem Possible solutionThere is water on the floor.• Make sure that the couplings of the water hoses are tight and thereis not water leakages.• Make

CAUTION! Risk of injury! Makesure that the drum is not rotating.If necessary, wait until the drumstops rotating.Make sure that the water levelinside t

PRODUCT INFORMATION SHEET IN REFERENCE TO E.U. REGULATION1369/2017Product Information SheetTrade Mark ZANUSSIModel Z712W43BI,PNC914580201Rated capacit

Airborne acoustical noise emission in db(A) spinning 78Built in appliance Y/N YesThe information given in the chart above is compliant with the EU Com

38

39

Contact the Authorised Service Centre toensure which accessories can be used.ELECTRICAL CONNECTIONWARNING! Risk of fire and electricshock.• The applia

WWW.ZANUSSI.COM/SHOP157018371-A-462018

THE APPLIANCE IS EQUIPPED WITH ...x1 x2x1Ex2x1 x1x1 x2x4 x1 x1BA C DF G H LUNPACKINGWARNING! Use the gloves.WARNING! Remove all the packaging and the

124. Return the appliance in vertical position andremove the socket polystyrene protection.5. Remove the power supply cable and the drainhose from the

If possible, install the appliance where the floor ismore stable.POSITIONING AND LEVELLINGx41. Install the appliance on a flat hard floor.WARNING! Mak

The inlet hose1. Remove the inlet hose from inside the drum.2. To connect the water inlet hose towards the prop-er direction and with the proper incli

Ø 40 mmTo a stand pipe with vent-holeDirectly into a drain pipe at a height of not less than60 cm (23.6”) and not more than 100 cm (39.3”).The end of