ENUser manualWashing MachineZWI 71201 WA
ProgrammeMaximum and Minimum TemperatureCycle DescriptionMaximum Spin SpeedMaximum Fabrics LoadType of LaundryOptionsDetergentCompartmentSOAK 30°Prewa
ProgrammeMaximum and Minimum TemperatureCycle DescriptionMaximum Spin SpeedMaximum Fabrics LoadType of LaundryOptionsDetergentCompartmentSPIN Drain an
Programmes Load(kg)Energy con-sumption(kWh)Water con-sumption (litre)Approximateprogramme du-ration (mi-nutes)Remainingmoisture(%)1)Standard 40 °Ccott
quantities to avoid waste and protect the envi-ronment.Although biodegradable, detergents containsubstances which, in large quantities, can upsetthe d
1. Before pressing button 7: it will be impossi-ble to start the machine.2. After pressing button 7: it will be impossi-ble to change any other progra
different speed. The relevant pilot light illumi-nates.Select the available options by means ofbuttons 3, 4, 5 and 6Depending on the programme, differ
Cancelling a programmeTurn the selector dial to to cancel a pro-gramme which is running. Now you can select anew programme.Opening the door after th
Remove the drawerby pressing the catchdownwards and bypulling it out. Flush itout under a tap, to re-move any traces ofaccumulated powder.To aid clean
Caution! When the appliance is in useand depending on the programme selectedthere can be hot water in the pump.Never remove the pump cover during a wa
• screw the pump cover again and close thedoor.Important! Every time you drain the waterthrough the emergency emptying hose you mustpour 2 litres of w
ContentsSafety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3Product description _ _ _ _ _ _ _ _ _ _ _
Problem Possible cause/SolutionThe machine does not emptyand/or does not spin:The drain hose is squashed or kinked. • Check the drain hose connection.
Problem Possible cause/SolutionSpinning starts late or themachine does not spin:The electronic unbalance detection device has cut in because the laund
After removing all thepackaging, carefullylay machine on it'sback to remove thepolystyrene base fromthe bottom.Remove the powersupply cable and t
Open the porthole and extract the inlet hose.Connect the appropriate end of the hose tothe appliance with the angled connection asshowed in the pictur
Caution! Should the appliance powersupply cable need to be replaced, thismust be carried out by a Service Centre.Building inThis appliance has been de
• a) DoorThe dimensions of the door should be:- width 595-598 mm- thickness 16-22 mmThe height (C-Fig. C) depends on the heightof the adjacent furnitu
Environment concernsRecycle the materials with the symbol . Putthe packaging in applicable containers torecycle it.Help protect the environment and
27www.zanussi.com
www.zanussi.com/shop 132928492-A-182013
• Do not change the specification of this appliance.• Obey the maximum load volume of 8 kg (refer to the “Programmechart” chapter).• If the supply cor
Water connection• Make sure not to cause damage to the waterhoses.• The appliance is to be connected to the wa-ter mains using the new supplied hose-s
To activate this de-vice, rotate the button(without pressing it)inside the door clock-wise until the grooveis horizontal. If neces-sary use a coin.To
1 32 4 5 6 791081Programme selector dial2SPIN reduction button3OPTIONS button4PREWASH button5EASY IRON button6EXTRA RINSE button7START/PAUSE button8DE
Door lockedProgramme selector dial, spin speed button and available optionsProgramme Selector DialIt allows you to switch the appliance on/off and/or
This device permits you to leave the applianceunattended during it's functioning.10.2:• Duration of the selected programmeAfter selecting a progr
ProgrammeMaximum and Minimum TemperatureCycle DescriptionMaximum Spin SpeedMaximum Fabrics LoadType of LaundryOptionsDetergentCompartmentHANDWASH 40°
Kommentare zu diesen Handbüchern